How to propagate snake plant? | in Water from Leaf Cuttings

Propagation of a Sansevieria plant is easy. If you already have one, you can multiply the leaves to form more plants. Snake plants (Sanssevierias) are one of the easiest to maintain indoor plants. Rooting cuttings of snake plants in water is foolproof. Being patient could be the hardest part.

Want to know more about your snake plant?

Get all the tips to keep your plants happy and healthy. Come to my other articles about the care of your Sansevieria.

Snake Plant Propagation

Here are a few reasons why you should propagate your snake plants and why only occasionally, if at all.

You may want to adjust the general appearance of your plant a little and remove some leaves. These can grow back into your indoor plant collection or be used as a thoughtful gift for friends and family. Use damaged leaf or sunburn spots or leaves that become too large and bend or break off. When you water your Sansevieria, your plant roots rot. It is not all bad, and you can save them and multiply the parts that are still healthy.

Easy Propagation Tips

For the fastest results, use healthy leaves that are not too old. Be prepared to exercise patience. Cuttings from snake plants can take a long time to take root. However, this is fast, so don’t expect any results overnight.

Cut a V-shaped notch into the underside of the leaf. It is important to keep the pruning in the same direction in which it was planted. If you turn the cut upside down, it doesn’t root. Snake plants do not grow roots. Some say it doesn’t work, but that’s because they can’t wait.

The only way to prevent the multiplication of the variety is to multiply the plants in the division. If you propagate a colorful Sansevieria with a yellow edge, new leaves will grow from the cuttings that do not color the yellow edge. Separate the clumps of leaves and roots from the main plant and pot them into their own pots. This increases the surface on which the roots grow, and it is possible to see which side ends are introduced into the water and soil.

How to Propagate Snake Plants in Water

You can multiply a single leaf by placing it in a tall glass vase for dramatic effect. Cut the leaf into several sections. Use a clean, sharp cut or scissors to cut the leaf out of the ground. In this way, a new plant can be grown from it.

Place your cut in a glass jar with enough water to cover the lower part of the cut. Leave to dry for a few days or until the cuts are numb. This is important to prevent the cut from rotting. For me, cuttings with pointed tips tend to have a higher success rate and seem to let roots and new leaves grow a bit faster.

Put it outside where it gets a lot of indirect light. Change the water approximately every few days. This is where the wait begins.

You will have to wait about a month for the roots to take root. Don’t worry if it’s a month and you haven’t seen the roots. Wait until the roots are at least one centimetre long before potting them into well-drained, juicy soil. Then the puppies start to grow.

Mix in some perlite or pumice stone for better drainage (e.g.: and so on).

Have a look at my article on water propagation if you want to know more about growing new plants in water (i.e.

How to Propagate Snake Plant cuttings in Soil

I love roots in the water and enjoy seeing them grow. But I understand that if I want to do something, I have to do it right.

In some cases you can propagate your Sanseveiria by taking cuttings in the ground. Cut off your leaf, make it numb, lay it in the ground and wait. Keep the soil moist so that the roots have less to do before they take root. With this method, the water content is completely skipped.

It is the tip of the leaf if it is intact. The pruning itself will not grow back. You will see new leaves appear when you cut back the original cut.

To speed up the process a bit, you can use root hormone powder on your cut. Fill a small pot with moist, well-drained succulent soil and stick your cut about 1 / 2 inch deep. Dip the cut into the water and dip the bottom 1 / 4 inch into the root powder.

How to propagate snake plants. Propagation problems

Proper propagation of snake plants is far from foolproof, and it just so happens that it does not always work as planned. Some cuttings do not take as long as others.

Answer: If your snake plant cuttings do not form roots, give them a little more time. They do not rot in the water, so keep fresh and roots appear.

Leaves get mushy and brown

Tip: Learn about the basics of watering and get all the tips for watering indoor plants correctly. Watch out for cuttings of snake plants that get a bit mushy and start to go down and take on a brown or black color. If this happens to cuttings that are sitting in the water, it is likely that they are not dry enough to put them back in the water. When cuttings begin to rot in the soil, this is an indication that they have suffered from overwatering. Overwatering is caused when you water a cut or plant in the soil, especially if it is in a pot with a large drain hole at the bottom.

Propagating other Succulents from leaves

In the water on the ground or by doing nothing. Succulents have leaves that can be propagated in three ways. Many are propagated by growing a new plant from a single leaf. Here are some types of succulents that you may want to propagate.

Don`t copy text!